Why this watchmaker tool belongs on your bench
The Precision screwdrivers – Watchmaking repair set is a precision screwdriver designed for the small slotted screws found on screw-back watches and watch movements. It is built from silvered stainless steel shaft about 7.5 cm long and 0.4 cm wide, with a freely rotating top cap and a flat ground tip of about 2 cm; tip sizes 0.80, 1.00, 1.20, 1.40 and 1.60 mm and is used for unscrewing and re-screwing the tiny slot-head screws found on screw-back case-backs, movement bridges, clasp covers and similar parts. This watchmaker tool suits every screw-back watch and movement work, plus eyeglasses, hobby electronics and any precision device with miniature slotted screws, so it slips naturally into the routine of anyone who services watches, hobbyist or professional alike.
If you have ever struggled with a slipping screwdriver, a stubborn case-back or a crown that refused to grip, you already know why a properly sized, well-built watchmaker tool matters more than its modest price. Around the workshop bench this kind of accessory pays for itself the very first time it spares a marred case or a chewed-up screw head.
A closer look at the tool
Look closely and you see a tool that has been thought through. The working surface – be it a blade, a jaw, a tip or a lens – is shaped for the exact job it has to do, and nothing else. Materials are chosen for the right balance of hardness and ductility, and dimensions are tuned to fit the typical hand and the typical wristwatch. Silvered stainless steel shaft about 7.5 cm long and 0.4 cm wide, with a freely rotating top cap and a flat ground tip of about 2 cm; tip sizes 0.80, 1.00, 1.20, 1.40 and 1.60 mm: that combination means the tool can be picked up, used and put down dozens of times in a row without fatigue.
The intent is to keep your attention on the watch rather than on the tool itself. A precision accessory should disappear in the hand and let the case, the movement, the metal bracelet stay the focus of the work. That is the design philosophy you will recognise as soon as you take the first few measurements or open the first case-back.
Technical specifications
- Type: precision screwdriver designed for the small slotted screws found on screw-back watches and watch movements
- Build: silvered stainless steel shaft about 7.5 cm long and 0.4 cm wide, with a freely rotating top cap and a flat ground tip of about 2 cm; tip sizes 0.80, 1.00, 1.20, 1.40 and 1.60 mm
- Main use: unscrewing and re-screwing the tiny slot-head screws found on screw-back case-backs, movement bridges, clasp covers and similar parts
- Compatibility: every screw-back watch and movement work, plus eyeglasses, hobby electronics and any precision device with miniature slotted screws
- Variants: Five tip sizes available: 0.80, 1.00, 1.20, 1.40 and 1.60 mm.
When and why to use it
You will reach for this watchmaker tool whenever you need unscrewing and re-screwing the tiny slot-head screws found on screw-back case-backs, movement bridges, clasp covers and similar parts. In practical terms that means every screw-back watch and movement work, plus eyeglasses, hobby electronics and any precision device with miniature slotted screws. Even seasoned collectors sometimes underestimate how much smoother a job becomes when the dedicated tool is on the bench, rather than an improvised substitute borrowed from a kitchen drawer.
Using the right watchmaker tool also protects the value of the watch. Vintage cases are particularly sensitive: a single deep scratch on a brushed lug or a chewed slot on a stainless screw head can knock down the resale value far more than the cost of buying the correct accessory in the first place.
How to use it step by step
The handling routine is simple, but doing it well makes the difference between a clean job and a regret. Follow these steps:
- Choose the tip size that matches the screw – the blade must fill the slot without forcing it.
- Rest your index finger on the rotating top cap so the screwdriver spins on its axis under finger pressure.
- Engage the tip squarely in the slot, keeping the shaft perfectly vertical.
- Apply downward pressure first, then turn slowly. The free-spinning cap lets the wrist stay still while the shaft rotates.
- Pull the screw out with the magnetised tip or with tweezers, and store it in a parts tray so it cannot roll away.
Take it slow on the first few attempts. With a relaxed grip and a steady wrist, the gesture quickly becomes natural. Most beginners gain confidence after three or four real-world repairs and never look back.
Build quality and care
The watchmaker tool is forged or machined and then ground to size. Surfaces are smoothed enough to avoid leaving marks on the watch but textured where a non-slip grip is required, so the tool behaves predictably even with slightly damp fingers.
To keep the watchmaker tool in form for years, give it three small kindnesses: wipe it clean after use, store it in a dry place, and never use it for jobs it was not designed for. A precision accessory pressed into duty as a chisel or a screwdriver loses its edge quickly. Treated well, it can comfortably outlast the watch on your wrist.
Frequently asked questions
Is this tool suitable for beginners in watchmaking?
Yes, this is one of the more approachable watchmaker tools. The technique is intuitive and, with a soft bench cushion and a steady hand, the risk of damaging the case, the crystal or the gasket stays low.
Which kinds of watches does it work with?
Suitable for any wristwatch with slotted micro-screws, plus eyeglasses, drones, vintage cameras and similar precision objects.
How should I clean and store the tool?
Wipe the tool dry after each use, especially after contact with cleaning fluids or silicone gasket grease. Store it in a dry drawer or a roll-up pouch; a very thin film of light machine oil protects the steel parts in humid workshops.
Browse our full range of watchmaker tools to complete your repair kit and keep every favourite watch ticking for years to come.
